Transitmania 10 @Santa Pod 18th to 20th May 2018


MK 2/3/4/5) 2.5 Di clutch judder

Before you ask a question, check to see if it's been asked before. We show all the common Transit faults here and it's a good idea to read through these in case they happen to you in the future!!

MK 2/3/4/5) 2.5 Di clutch judder

Postby Wreckersinternational » Wed Jul 19, 2006 9:22 pm

Hi, Can anybody tell me the likely cause of the clutch judder on my 1990 190, 2.5 diesel/ MT75.
Wreckersinternational
Transit Addict
Transit Addict
 
Posts: 77
Joined: Thu Jul 21, 2005 6:43 pm
Location: Devizes

Re: MK111 clutch judder

Postby Luke » Wed Jul 19, 2006 9:32 pm

Wreckersinternational wrote:the likely cause of the clutch judder
a common Di one is oil leaking from the crank seal- if you can live with it its not a major hassle :lol:
User avatar
Luke
Site Admin
 
Posts: 41661
Joined: Wed Mar 02, 2005 12:53 am
Location: Rotherham, Yorkshire!!

Postby motorwise » Wed Jul 19, 2006 9:56 pm

as said oil on lining also soft engine mounts or a tired clutch - on these it's usually a tired clutch - good luck
Ford Transit - Backbone Of Britain
http://www.motorwise.net
if you want to get on in life, its not what you know, its not who you know, its what you know about who you know
User avatar
motorwise
Transit Extremist
Transit Extremist
 
Posts: 7992
Joined: Thu Apr 20, 2006 1:49 am
Location: Bromley Kent

Postby jay » Thu Jul 20, 2006 2:09 pm

mine judder a little when pulling away and in reverse and its got a new clutch in.and good engine mounts..
another bit to check is the rear gearbox mount bolts are still tight..
100ps mk6 in moondust silver with mk7 front end
User avatar
jay
Transit Extremist
Transit Extremist
 
Posts: 7868
Joined: Tue Jul 05, 2005 6:24 pm
Location: Redditch.

Postby madmark » Thu Jul 20, 2006 2:53 pm

:? its very comon falt with the transit , my mk1 does it as well! :(
madmark
Transit Extremist
Transit Extremist
 
Posts: 15497
Joined: Thu Mar 03, 2005 4:29 am

Postby Neil » Thu Sep 21, 2006 7:30 pm

new clutch soon
Neil v6
Neil
Transit Extremist
Transit Extremist
 
Posts: 5424
Joined: Sun May 01, 2005 5:09 pm
Location: Preston

Postby chris13 » Tue Oct 03, 2006 2:01 pm

It can be a rusty imput shaft, especially on older or unused vehicles. Clean up and dab a little copper grease on the splines, but not too much.
chris13
Transit Aficionado
Transit Aficionado
 
Posts: 289
Joined: Thu Aug 03, 2006 8:34 am
Location: Dewsbury

clutch judder

Postby martin lewis » Sat Dec 09, 2006 7:15 pm

if you have the clutch off take the flywheel off and have your local engineering shop check the run out, i had vicious judder which turned out to be a distorted flywheel , re-machining the working faces fixed the problem.
martin lewis
Transit Fan
Transit Fan
 
Posts: 11
Joined: Fri Dec 08, 2006 11:23 pm
Location: watford herts uk

Postby mexico » Wed Dec 13, 2006 12:03 am

Had the same problem, the propshaft centre bearing was wrecked, but wasn't cured completely until new clutch fitted.
mexico
Newbie
 
Posts: 4
Joined: Tue Dec 12, 2006 9:37 pm

clutch

Postby hentpe » Wed Dec 13, 2006 8:54 am

Sticky clutch cable could be the cause too.
Petri Henttula
hentpe
Transit Addict
Transit Addict
 
Posts: 49
Joined: Tue Nov 28, 2006 7:21 pm
Location: Mynämäki, Finland

Postby sam l » Tue Dec 19, 2006 11:24 pm

My MKII does it too. It seems to be better when cold and when it's had some stick, which I suppose suggests it's an oil thing.
sam l
Transit Addict
Transit Addict
 
Posts: 95
Joined: Tue Dec 19, 2006 11:22 pm

2.5di Clutch Judder

Postby TransitNut » Mon Jan 01, 2007 11:43 pm

I've had this problem since fitting a "reconditioned" gearbox along with a new clutch to my Mk5.

I Fitted a new crank seal and input shaft bearing (Genuine Ford) at the same time as the gearbox, so in theory the rear crank oil seal output bearing and clutch should have been OK!

The problem doesn't exist when the engine is cold but worsens when up to normal temperature and is highlighted even more when loaded.

Keeping the revs a little higher than would normally be required when pulling away or reversing makes the problem dissapear.

So I investigated all the usual recommendations engine/gearbox mountings, propshaft alignment & bearings, rear diff bearings all to no avail.

So I removed the gearbox (for the 4th time, don't ask) and the clutch, and it could be seen that the clutch plate hadn't been running perfectly true by the marks on the flywheel, further investigation revealed the input shaft on the gearbox is very slightly worn at the point where it sits inside the rear crankshaft output bearing.

I'd retained the old bearing (which wasn't at all worn but as I'd bought a replacement I had fitted the new one), and discovered after taking some accurate measurements I could install both bearings into the crankshaft and install the gearbox OK.

This hasn't entirely celared the judder but has improved things until I can get "another" replacement gearbox this time without a worn input shaft.
User avatar
TransitNut
Newbie
 
Posts: 6
Joined: Fri Oct 14, 2005 4:13 pm
Location: Staffordshire

Clutch Judder

Postby Terry » Tue Jan 30, 2007 8:43 am

If its a case of oil on the clutch plate a get you home measure is,
squirt some of the contents of a C.T.C.(Carbon Tetra Chloride) fire extinguisher into the bell housing while someone operates the clutch..
(its what the 'dry cleaners' use to degrease clothes).
I got a little black book with me poems in
Pallet Puller
Terry
Transit Fanatic
Transit Fanatic
 
Posts: 2271
Joined: Fri Dec 02, 2005 9:47 am
Location: Sunbury On Thames

Re: Clutch Judder

Postby ace_paul » Sat Oct 13, 2007 4:36 pm

[quote="Terry"]If its a case of oil on the clutch plate a get you home measure is,
squirt some of the contents of a C.T.C.(Carbon Tetra Chloride) fire extinguisher into the bell housing while someone operates the clutch..
(its what the 'dry cleaners' use to degrease clothes).[/quote]

How much do we squirt in the bell housing?
Who needs to inhale to most for best results, the van or us?

Oh, try putting the plate in boiling water.
(works on brakes, have tried it)
ace_paul
Newbie
 
Posts: 1
Joined: Wed Oct 10, 2007 11:03 pm

Re: 2.5 Di mk3 clutch judder

Postby bjw » Sun Dec 16, 2007 5:45 pm

Can also be worth checking the tension of "u" bolts on rear springs.
bjw
 
Posts: 0
Joined: Sun Dec 16, 2007 5:19 pm

Next

Return to Frequently asked questions!!



Who is online

Users browsing this forum: No registered users