*NOW BOOKED FOR 2024* Transitmania 15 @ Santa Pod 19th to 21st July 2024 *ALL DETAILS HERE*


Connect - Coding Keys & Programming for remote C/Locking

Use this section to post all specific Transit Connect topics and questions

Connect - Coding Keys & Programming for remote C/Locking

Postby paul2012 » Thu Jul 06, 2017 1:36 am

Transponder types (immobilser chips in keys)

Connect from 2003-2006 uses ID4D-60 (Glass) as shown below

DSCF5294_zps3d69fe8a.jpg


Connect from 2006-2013 uses ID4D-63 (W1 carbon chip) as shown below

key_zps9de24bf8.jpg


A 3 button remote key can also be programmed to connects for remote central locking & PATS (immobilser)
make sure you get the correct one for your connect - see below

DSCF6798_zpse3c66220.jpg


KEYSAB_zps0fa2aae7.jpg


Blank key blade are available from Ford for £8 - they will even cut it for you :D

Coding transponder/keys to PATS on connects from 2003-2009

**NOTE** :- A maximum of eight keys (including the ones supplied with the vehicle)
Can be coded using two other keys previously coded for your vehicle.
Complete the following steps within five seconds.

1. Insert the first key in the ignition switch and turn to position II.
2. Turn the key back to position 0 and remove from the ignition switch.
3. Insert the second key in the ignition switch and turn to position II.
4. Turn the second key back to position 0 and remove from the ignition switch − the key coding mode is now activated.
5. If an uncoded key is now inserted in the ignition switch and turned to position II within 10 seconds, this key is coded to the system.
6. After the coding process is completed, remove the key from the ignition switch. Wait five seconds for the system to be activated.
If coding is not completed correctly, the indicator light flashes after the ignition is switched on with the newly coded key and the engine will not start.
Repeat the coding process after waiting 20 seconds with the ignition switched on (position II).

Programming 3 button romote key/fob for remote central locking on connects from 2003-2009

1. Close all the doors.
2. Turn Ignition key from position 0 to II eight times within 10 seconds.
3. Locks will cycle (locks then unlocks the doors.)
4. Press the button on the remote fob / 3 button key within 20 seconds, the locks will cycle again (locks then unlocks)
7. Turn the ignition key to position 0 to exit the programming mode.

**NOTE** : Maximum 4 remote fobs/keys may be programmed.


Programming 3 button remote key/fob for remote central locking on connects from 2009-2013


1. Turn ignition key to position II four times within six seconds.
2. Turn the ignition to position 0. A tone sounds to indicate that it is now possible to programme the remote controls for ten seconds.
3. Press any button on a new remote control. A tone will sound as confirmation.
4. Repeat this last step for all your remote controls, including your original. Do not remove the key from the ignition when pressing the button on this remote control.
5. Switch the ignition back on (position II) or wait for ten seconds without programming another remote control to end the key programming.
Only the remote controls which you have just programmed are now able to lock and unlock the vehicle.
You do not have the required permissions to view the files attached to this post.
Last edited by paul2012 on Thu Jul 06, 2017 1:47 am, edited 1 time in total.
2007 Ford Mondeo mk4 1.8 TDCI -RETROFIT IN PROGRESS
2009 Jaguar X-Type 2.0D
2010 Vauxhall Insignia- RETROFIT IN PROGRESS

IDS & GM GDS2 services


SUBSCRIBE http://www.youtube.com/@PaulsTechChannel
User avatar
paul2012
Transit Extremist
Transit Extremist
 
Posts: 7445
Joined: Sun May 13, 2012 8:59 pm
Location: Nr Wretton, Norfolk

Re: Connect - Coding Keys & Programming for remote C/Locking

Postby paul2012 » Thu Jul 06, 2017 1:46 am

Regarding Mondeo / Focus mk2/3 flip key remote.

DSCF3568.jpg


These use a ID4D-63 (W1 carbon chip) can be used for connects from 2006-2013
BUT key blade will require changing to Tibbe. Then program to vehicle for central locking & PATs (Immobilser)

Note transponder is located next to keyblade - see below

DSCF6806_zps18261f66.jpg


Carefully seperate casing without breaking it :!: to retrieve transponder chip.

DSCF5293_zps086ba3a0.jpg


DSCF6751_zpsb8880051.jpg


Modify casing to except glass transponder chip :wink:

DSCF6808_zpsceb832e9.jpg


Then program remote fob for central locking. Follow instructions posted at start of this thread. 8)
You do not have the required permissions to view the files attached to this post.
2007 Ford Mondeo mk4 1.8 TDCI -RETROFIT IN PROGRESS
2009 Jaguar X-Type 2.0D
2010 Vauxhall Insignia- RETROFIT IN PROGRESS

IDS & GM GDS2 services


SUBSCRIBE http://www.youtube.com/@PaulsTechChannel
User avatar
paul2012
Transit Extremist
Transit Extremist
 
Posts: 7445
Joined: Sun May 13, 2012 8:59 pm
Location: Nr Wretton, Norfolk


Return to Transit Connect



Who is online

Users browsing this forum: Majestic-12 [Bot]

This site contains affiliate links for which we may be compensated.