What did you do to your Custom today?

[Camper steve]

looks good, lots of storage.

mine is here viewtopic.php?f=65&t=163691


the sink unit fits on slotted hooks and a bit of bunji cord to keep it held down on hooks, the power for the pump is piggy backed through a fuse from the power socket in the rear and is on a plug/socket, so this can lift out as a unit in seconds. the black box to the right is a fridge box which plugs into the 12v socket at the rear of the van.

[Jobbo]

The concerns and recent events have been praying on my mind, so I've just fitted and OBD Box and Hykee door lock.., just needed to scratch my head and think about it first..lol

IMAG1124.jpg

IMAG1126.jpg

[khould]

Had windows fitted in the new Limited today, next job for the camper conversion is the insulation and ply lining

Kev

[Tom101]

ECU Tuning
http://www.gcstuning.pl/

Transit Custom Trend 2013 2.2 / 82500 miles
Dyno test :
From 125 HP (Drive shaft- Ford info) 118 HP at 3931 RPM (Wheels reality) to 182 HP at 4160 RPM (Wheels)
From 308 Nm at 2031 RPM to 421 Nm at 2560 RPM ( Wheels)

Speed limiter ( 90 m/h max ) removed

Now flying torpedo..

[Dave17355]

Nice little wheel mod

Where are they from please and size?


Sent from my iPhone using Tapatalk

[bigjohnthomas]

What's all these wires doing milling about by the back doors ?
They are just asking to be eaten
am I missing something here?
Going to have to ply both holes up
Bloody ford

[John Johnson]

Had the Euro 6 van about 6 months now and it was ceramic coated from new , I've just applied a topper coat on it and clay barred it prior to this and it pulled very little contaminants off it ... very impressed

[loot]

What's all these wires doing milling about by the back doors ?
They are just asking to be eaten
am I missing something here?
Going to have to ply both holes up
Bloody ford

They are ground wires, probably from the oil slick cannons that keep the feds away

[Camper steve]

fitted the passenger seat swivel from Kirivans today. Im pleased but the instructions were crap, wait a minute, there were no instructions what so ever, so that would explain why they are crap...... still like it though.

[loot]

Easy fella the custom has only been out since 2012 nobody knows about them

[customed]

The concerns and recent events have been praying on my mind, so I've just fitted and OBD Box and Hykee door lock.., just needed to scratch my head and think about it first..lol

IMAG1124.jpg

IMAG1126.jpg

where did you get that door lock if you dont mind me asking?

[botacco]

Just installed a solbian semi flexible 210w panel (CV210) and victron blue solar MPPT to charge the leisure battery during camping.

As all my mods, the basic idea was to have a 100% reversible. I didn't want to drill the roof, glue the panels neither to use the roof-bar holes to avoid any water issues and therefore I decided to glue the panel to a 10mm polycarbonate panel.





[img width=640 height=360]https://uploads.tapatalk-cdn.com/20170124/ac8e27e597e3e0743ace12ca230db52a.jpg[/img]

I installed a plastic cable rail below the panel, to keep the distance from the roof and help the MC4 connectors.


Finally I wrapped the borders with aluminium tape, just for aesthetical reasons.











The panel produces 6w @ 13.00 (Jan. 30th) with no sun and 45W under the sun... I hope will be better this summer...



I will fix cables this spring, as soon as the temperature will be higher than 16 degrees (the glue and any adhesive tape are not working below 16C)




And here is the mess... I am going to organize the cables better in an electric plastic box this week

[BHM]

Changed rear pads.
3 pads at 4mm
1 pad at 0.5mm and its one without a sensor.

Bit of a pain aligning pin on back of pad with slot in caliper piston face.

Mileage of 36K miles, but inner city work

BHM

[FlyCatcher]

HYKEE lock fitted today.

[stchris356]

I disconnected the global unlock from the drivers door lock so if some scum bag decides to hammer a screwdriver in the door lock, or pick the lock, it won't unlock the whole van!