What did you do to your mk6/7 today?

[ned]

Erm, oooops

IMG_3839.jpeg

IMG_3841.jpeg

Think a weldathon is called for

[mjsroofing]

I have finally fitted the high spec clocks in my mk7, I've only had the van for 13 years lol.

Big thanks to loot once again for his details on how to add wires.

Cruise control and outside temp next. But I need to fit new bcm for that.

[loot]

Good jobs

I bought an ac refill can with gauge and tube to install the gas. Everywhere says the thick ac pipe is low pressure, my van only fits the small ac pipe that is right at the firewall, i plugged into that and opened the tap, the dial went to 50psi right at the maximum side of the green zone. Can is empty now. Maybe 300ml can? Ac is still blowing cool though

[loot]

Erm, oooops

IMG_3839.jpeg

IMG_3841.jpeg

Think a weldathon is called for

Easy enough job that

[loot]

I have finally fitted the high spec clocks in my mk7, I've only had the van for 13 years lol.

Big thanks to loot once again for his details on how to add wires.

Cruise control and outside temp next. But I need to fit new bcm for that.

Glad it's sorted

[loot]

Good jobs

I bought an ac refill can with gauge and tube to install the gas. Everywhere says the thick ac pipe is low pressure, my van only fits the small ac pipe that is right at the firewall, i plugged into that and opened the tap, the dial went to 50psi right at the maximum side of the green zone. Can is empty now. Maybe 300ml can? Ac is still blowing cool though

[ned]

Erm, oooops

IMG_3839.jpeg

IMG_3841.jpeg

Think a weldathon is called for

Easy enough job that

Aye started just need to do a bit of patching and stitch weld

IMG_3923.jpeg

Trying to decide how best to do the arch without removing the door

[loot]

Erm, oooops

IMG_3839.jpeg

IMG_3841.jpeg

Think a weldathon is called for

Easy enough job that

Aye started just need to do a bit of patching and stitch weld

IMG_3923.jpeg

Trying to decide how best to do the arch without removing the door

Get a permanent marker and draw round the door hinges. Then you can remove the door and refit it without famnying about. Hardee's bit is unplugging the electrical connector

[Airthies]

Erm, oooops

IMG_3839.jpeg

IMG_3841.jpeg

Think a weldathon is called for

Think that's beyond a gynecologist scope if your fanny has a hole that large and crusty.

Sent from my Pixel 8a using Tapatalk

[ned]

Erm, oooops

IMG_3839.jpeg

IMG_3841.jpeg

Think a weldathon is called for

Think that's beyond a gynecologist scope if your fanny has a hole that large and crusty.

Sent from my Pixel 8a using Tapatalk

My fanny flaps seem to be parting leaving a gaping bucket hole, it’s like putting a cocktail stick in a 205L barrel

IMG_4088.jpeg

The hard bit is finding something to weld to

[ned]

Fitted a new turbo, what a pain to get to one nut for the oil return pipe, welded up all the holes and unleashed a fook load of underseal on everything forgot to get pictures, just got to turn the eml off and tidy the back up then hopefully mr yellow crayon man can fit me in tomorrow or Tuesday for the annual how much damage have pot holes caused test

[loot]

Anyone notice that the mk7 seems to have a software glitch. Throttle about 2k revs and it has the odd miss fire think I've had nearly all mk7 with it

[ned]

I’ve noticed a weird occurrence in 5th around 2k revs when or after rain that the engine kind of bounces and the gear stick shakes, so annoying

[gotgcoalman]

I’ve noticed a weird occurrence in 5th around 2k revs when or after rain that the engine kind of bounces and the gear stick shakes, so annoying

Sitting on
it during such times will make you smile.
Oh and potentially have an accident.

Sent from my LE2101 using Tapatalk