*NOW BOOKED FOR 2026* Transitmania 17 @ Santa Pod 17th to 19th July 2026 *ALL DETAILS HERE*


P00BD - 00 Air flow too high

Use this forum to post technical questions & problems about any Transit

Moderator: Luke

P00BD - 00 Air flow too high

Postby Hobbsy23 » Wed Sep 30, 2020 12:53 pm

Hi I have a transit custom 2016 limited spec 155 and I’m getting a fault code

P00BD - 00 Mass or volume air flow A circuit range / performance -Air flow too high

Have fitted a new sensor in air box have fitted new sensor in intercooler and problem still there I have reset values also. Can’t see any holes in intercooler pipes and when I block air intake van cuts out

Can any one help?
Hobbsy23
Newbie
 
Posts: 7
Joined: Tue Jun 07, 2016 10:32 am

Re: P00BD - 00 Air flow too high

Postby loot » Wed Sep 30, 2020 1:26 pm

Has the egr been blanked?
56 350 2.2 130ps mk7 with 2 side doors 8)
65 290 2.2 125ps custom with 2 side doors 8)
07 350 170ps
Ids v86 licence + v86.04 update + xprog here
Ids map here
User avatar
loot
Site Moderator
 
Posts: 34208
Joined: Sat May 05, 2012 6:06 pm
Location: North Wales

Re: P00BD - 00 Air flow too high

Postby Frag » Wed Sep 30, 2020 7:29 pm

And have you checked the condition / correct fitment of the air filter itself ?
User avatar
Frag
Ford Technician
 
Posts: 5115
Joined: Sat Jul 05, 2008 3:05 pm

Re: P00BD - 00 Air flow too high

Postby Jim Archer » Mon Oct 05, 2020 9:54 am

EGR stuck open/not closing fully?

Jim
Mk7 140 Jumbo - Vantunered.
289,000 and counting.
Jim Archer
Transit Fanatic
Transit Fanatic
 
Posts: 3434
Joined: Sat Sep 29, 2007 6:45 pm
Location: Southampton

Re: P00BD - 00 Air flow too high

Postby knobby1 » Mon Oct 05, 2020 8:28 pm

What the other lads have said....MAF and MAP sensors rarely fail and is usually the EGR causing the issue.

There are so many serviceable sensors being replaced for no reason....all to common unfortunately.

Lord Knobrot
2008 2.4L RWD 170+PS 6-speed 350 LWB High Roof..."Full Poverty Spec".

When I die, I want to go peacefully in my sleep like my Grandfather, not screaming like the passengers in his car..!
User avatar
knobby1
Transit Extremist
Transit Extremist
 
Posts: 18805
Joined: Tue Oct 21, 2014 1:36 am
Location: Brisbane, Australia

Re: P00BD - 00 Air flow too high

Postby aplcomms » Sun Jun 09, 2024 6:49 pm

My son has a 2013 Transit Custom. It recently developed a fault and gave the P00DB DTC. The DTC suggests that the MAF is faulty.

When analysing using Forscan, the Mass Airflow (MAF) and the Intake Air Temperature (IAT) appeared to be correct suggesting the combined MAF and IAT sensor on the Air Filter box were OK.

However, the Intake Air Temperature Sensor 2 (IATS2) was showing 126C even when the engine was cold. This sensor is located near the output of the Intercooler underneath the vehicle.

I had seen many YouTube videos and read many posts about this so I bought a new intercooler temperature sensor. The resistance at room temperature was around 11,000 ohms.

I connected my laptop with Forscan and IATS2 was at 126C. I unplugged the connector from the Intercooler sensor and temporarily fitted the new sensor to it. The IATS2 temperature was then 14C which was the same as the IAT. I removed the temperature sensor from the intercooler and fitted the new one and the IATS2 temperature behaved normally when the engine was started.

I measured the resistance of the old sensor and it was 519 ohms which is low and is a credible reading, but not a short circuit.

My conclusion is that these sensors go faulty with a low resistance but is not reported as faulty by the PCM. Instead the PCM incorrectly decides that the MAF is faulty, causing many to change the expensive MAF when there is no need to so so.

I hope that this helps.
aplcomms
Newbie
 
Posts: 1
Joined: Sun Jun 09, 2024 6:21 pm


Return to Technical Problems & Questions



Who is online

Users browsing this forum: No registered users

This site contains affiliate links for which we may be compensated.